Among Us: How to complete a mission in the map The Skeld

The only mission here is Swipe Card (Swipe the card) and it’s pretty simple. To do this, simply drag the lock card from your wallet at the bottom of the screen onto the reader, then swipe over. You cannot swipe it too fast or too slow, otherwise it will fail. Practice the manipulation well, so get used to it as soon as possible because this is one of the tasks that can take you time if you do not reach the correct swipe speed.

There are 2 missions in this room:

first. Upload and download data: Just click the download button and wait until the process is finished, then go to the admin room to upload the data according to the same procedure.

2. Dump the trash: Pull down the lever beside the trash can and hold it for a few seconds. Don’t release too soon or you won’t be able to perform the task. Then you need to go to the storage room to empty the trash by following the same procedure

Likewise, there are only two quests in this room

first. Download and upload data: Just click the download button and wait until the process is finished, then go to the admin room to upload the data according to the same procedure.

2. Switch power supply: First you need to access the equipment in the electrical room and redirect the power source by swiping the control bar to the highest level. You then need to go to the communications room and accept the redirected power supply by accessing the device and pressing the fuse in the middle of the board to allow the current to flow.

There are three missions in this room:

first. Download and upload data: Just click the download button and wait until the process is finished, then go to the admin room to upload the data according to the same procedure.

2. Wire repair: Just pull the ropes on the left side to their respective colors on the right to reattach. This task can take place in many different rooms, although the process is always the same.

3. Power supply pairing: You need to wait for the clock to align with the connectors on the right and light up. Once there, press the buttons on the right panel to lock them. You need to do that 3 times to complete the task. But be careful, if you get one step wrong, you will have to start over from step 1.

first. Align the motor output: Using the ruler on the right, align the engine layout on the left so that the blue line matches the red line in the center. When it fits, release the ruler. You need to align both the upper and lower engines to complete the task.

2. Redirects power to the motor above: You must access the unit in the electrical room and switch power to the upper motor by sliding the control bar all the way up. Then you need to go to the engine room above and accept the power to be diverted by accessing the device and pressing the fuse in the middle of the board.

3. Redirects power to the lower motor: You must access the unit in the electrical room and switch power to the motor below by sliding the control bar all the way up. Then you need to go to the engine room below and accept the power to be diverted by accessing the device and pressing the fuse in the middle of the board.

There are two missions here:

first. Check the sample: Just press the start button and wait 60 seconds for the counter to end. Then test the panel again and click the button corresponding to the sample with a different color from the rest. Specifically, there will be four blue patterns and one red pattern, choose the red pattern type to complete the task. You can do other quests in the meantime.

2. Send scans: Just interact with the scanner to scan itself. This process is automatic and only takes 10 seconds.

There are four missions in this room:

first. Charting course: You have to drag the spaceship across the screen from the starting point along the dotted line to the end point.

2. Download and upload data: Just click the download button and wait until the process is finished, then go to the admin room to upload the data according to the same procedure.

3. Switch the power supply to the navigation room: You must access the equipment in the electrical room and switch the power supply to the navigation room by sliding the control bar all the way up. Then you need to go to the navigation room and accept the redirected power supply by accessing the device and clicking on the fuse in the middle of the board.

4. Stable steering system: Drag the cross on the console to the center of the screen

There are three missions in this room:

1. Dump the trash: Click and drag down the lever beside the trash can and hold it for a few seconds. Don’t release it too soon or you will have to do it again. Then you need to go to the archive to empty the trash by following the same procedure.
2. Transfer the power supply to the oxygen room: You must access the equipment in the electrical room and switch the power supply to the Oxygen room by sliding the control bar to the highest level. Then you need to go to the Oxygen room and accept the power to be redirected by accessing the device and clicking on the fuse in the middle of the board.
3. Oxygen filter: Throw leaves falling into the trough to clean the air

There are two missions here

1. Start the reactor: To complete this quest, players memorize the exact position and order of the lights on the left panel and do the same in the right panel.

2. Unlock the Manifolds: You must click the number buttons in ascending order

There is only one task here, which is to transfer the power supply to the security room. You must access the equipment in the electrical room and transfer the power to the security room by sliding the control bar all the way up. Then you need to go to the security room and accept the redirected power supply by accessing the device and clicking on the fuse in the middle of the board.

There are two missions in this room:

first. Main shield: Just click on all the red hexagons to complete the mission

2. Transfer the power supply to the shield room: You must access the equipment in the electrical room and transfer the power to the shields by sliding its control bar all the way up. Then you need to go to the shield room and accept the power to be diverted by accessing the device and clicking on the fuse in the middle of the board.

There’s only one duty here, to refuel the engine. You have to go to the storage to refill a fuel tank first by holding down the button, then moving to the top engine to refill the engine, also by holding down the button. Repeat the same process for the lower engine to complete the task.

There are three missions in this room:

first. Meteorite destruction: Sit in the gunner’s chair and aim for the flying asteroids as they appear on screen to destroy them. Destroy 20 asteroids to complete the mission

2. Download and upload data: Just click the download button and wait until the process is finished, then go to the admin room to upload the data according to the same procedure.

3. Transfer the power to the weapon room: You must access the equipment in the electrical room and transfer the power to the weapon room by sliding its control bar all the way up. Then you need to go to the weapon room and accept the power to be redirected by accessing the device and clicking on the fuse in the middle of the board.

These are all quests in the map The Skeld. Fortunately, most of them are easy to complete with just a few clicks. However, if you know what to do in advance, you can save valuable time and possibly last longer. Right?